DESCRIPTION : 1118 S50 – FLOOR SELF 50, A cement-based, high-fluidity, self-leveling special leveling screed developed for thin applicationsLOOR – SELF 50, A cement-based, high-fluidity, self-leveling special leveling screed developed for thin applications...
** PLEASE CONTACT FOR PALLET PRICES.** PRODUCT INFORMATION ; DESCRIPTION : 1118 S50 – FLOOR SELF 50, A cement-based, high-fluidity, self-leveling special leveling screed developed for thin applicationsLOOR – SELF 50, A cement-based, high-fluidity, self-leveling special leveling screed developed for thin applications. AREAS OF USE: •Used for surface correction and leveling in all kinds of indoor areas. •Carpet, PVC and linoleum can be laid over it. •Can also be used alone as a floor covering. PRODUCT FEATURES •Can be walked on after 8-12 hours. •Depending on the ambient temperature, it can be covered after 48-60 hours. •Has high spreadability and adhesion. •Does not crack. •Easy and fast to apply. •Pumpable. TECHNICAL SPECIFICATIONS Flexural strength: Greater than or equal to 4 N/mm² Compressive strength: Greater than or equal to 20 N/mm² Adhesion to concrete (SS 92 35 07): Greater than or equal to 1 N/mm² Pot life of the ready mix: 15 – 20 minutes pH value: Approximately 11 *Typical values: Obtained as a result of tests performed on 4x4x16 cm mortar prisms at +23°C under 50% relative humidity conditions. High temperatures shorten the durations, low temperatures extend them. APPLICATION METHOD Surface Preparation : Before application, it must be determined that the surface to be coated is hard and sound; the surface must be freed from foreign matter, soft or weak layers. All dust and particles must be cleaned from the surface. Cement slurry or old coatings must be mechanically removed. Concrete stained with oil or grease may need to be cleaned by scorching with a torch and/or applying a special grease cleaner. Priming E 720 EMC should be applied onto the prepared surface with a soft brush or primer pump, ponding should be prevented and it should be allowed to dry (2 – 4 hours under normal conditions). If the absorbency of the floor to be applied is high, E 720 EMC should be diluted with clean water at a ratio of 1:5 for the first coat and 1:3 for the second coat. On sound concrete surfaces 1:3 A single coat diluted at the specified ratio is sufficient. If application on different substrates is in question, please consult Dolphinfix for dilution ratios and application techniques. E 720 EMC should not be applied to surfaces with a temperature below +10°C. The surface must be dry and the relative humidity must be below 70%. Insufficient drying time, low temperature and/or high humidity can affect film formation and prevent complete coverage of the surface. Mixing The material must be mixed with clean water at a ratio of 26% (6.50 liters per 25 kg bag). During the mixing process, a paddle attached to a drill bit or a pump approved by Dolphinfix must be used. When mixing with a paddle, the mixing time must not be less than 2 minutes. The mixed material must be used within 30 minutes, and the material temperature must be between +5° C and +20° C. Excessive cooling or heating of the dry material prior to use may affect the flow properties of the mixture. Application The mixed material is poured by spreading it over the surface. By passing over the material with a steel trowel or spiked roller, the release of air bubbles trapped inside the material is facilitated. Semi-hardened material can be easily shaped or cut, allowing desired corrections to be made. Floor Series products should not be applied to surfaces colder than +10°C. The floor must be protected against frost for 48 hours following the application. The ambient relative humidity must be below 70%. Mild ventilation is recommended during and after application, but dehumidifiers should not be used during the first two days. The use of curing membranes is not required. Following Floor – Self 50 application, structural and expansion joints as well as cracks that may continue to move must be transferred onto the new surface as joints. POINTS TO NOTE •Do not apply at temperatures below +5°C and above +35°C. •In exterior applications, in areas with a risk of freezing, the surface must be protected from sun, wind, rain or frost for the first 24 hours. •The working and reaction times of cement-based systems are affected by ambient and substrate temperatures and the relative humidity of the air. At low temperatures, hydration slows down, which extends the pot life and working time. High temperatures accelerate hydration and correspondingly shorten the times stated above. For the material to complete its setting, the ambient and substrate temperatures must not drop below the minimum allowed temperature. CONSUMPTION Depends on the surface to be applied. Dry material consumption is 1.5 kg/m² for 1 mm thickness. PACKAGING 25 kg kraft bag SHELF LIFE 6 months from the production date under suitable storage conditions. STORAGE CONDITIONS Store in unopened original packaging in a cool, dry environment, protected from frost. Do not stack more than 8 bags on top of each other.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: PAR 721 is a single-component, acrylic-based, water-based, ready-to-use primer material developed for glossy surfaces; it dulls the surface gloss, increases adhesion and improves the workability of the material to be applied over it.
DESCRIPTION: MicroFloor A 1001 MFA is a floor leveling screed consisting of special cements, fillers, binders and chemical admixtures that can be applied by hand or pump. It is developed to be applied at 1 – 5 mm thickness in a single coat.
DESCRIPTION: MFA 1002 is a floor leveling screed consisting of special cements, fillers, binders and chemical admixtures that can be applied by hand or pump. It is developed to be applied at 3-30 mm thickness in a single coat.
DESCRIPTION: 1119 S200 – FLOOR SELF 200 is a cement-based, highly flowable, self-leveling special leveling screed that can be applied at 20 mm thickness.