🌐 English ▾
📞 Customer Line 24/7539 303 00 72
🌐 English ▾
Home ›Flooring Solutions›Self-Leveling Screed ›1119 S200 – FLOOR SELF 200 Cement-based Leveling S...

1119 S200 – FLOOR SELF 200 Cement-based Leveling Screed (1-20 Mm)

489,50 ₺
Prices do not include %20 VAT; it is added at checkout.

DESCRIPTION: 1119 S200 – FLOOR SELF 200 is a cement-based, highly flowable, self-leveling special leveling screed that can be applied at 20 mm thickness.

KG:
Option:
📞 Request a quote for bulk / pallet purchases
🚚 Fast Shipping
🛡️ Secure Payment
↩️ Easy Returns
** PLEASE CONTACT FOR PALLET PRICES.** PRODUCT INFORMATION ; DESCRIPTION: 1119 S200 – FLOOR SELF 200 is a cement-based, highly flowable, self-leveling special leveling screed that can be applied at 20 mm thickness. AREAS OF USE; •Used for surface correction and leveling in all kinds of indoor areas. •Carpet, PVC and linoleum can be laid over it. •Can also be used alone as a floor covering. PRODUCT FEATURES; •Easily applied up to 20 mm. •Can be walked on after 12-18 hours. •Depending on the ambient temperature, it can be covered after 48-72 hours. •Has high spreadability and adhesion. •Does not crack. •Easy and fast to apply. •Pumpable. TECHNICAL SPECIFICATIONS; •Flexural strength: Greater than or equal to 4 N/mm² •Compressive strength: Greater than or equal to 25 N/mm² •Adhesion to concrete (SS 92 35 07): Greater than or equal to 1 N/mm² •Pot life of the ready mix: 15 – 20 minutes •pH value: Approximately 11 *Typical values: Obtained as a result of tests conducted on 4x4x16 cm mortar prisms under conditions of +23°C and 50% relative humidity. Higher temperatures shorten the times, lower temperatures prolong them. APPLICATION METHOD; SURFACE PREPARATION; Prior to application, the surface to be coated must be determined to be hard and sound; the surface must be cleared of foreign matter, soft, or weak layers. All dust and particles must be cleaned from the surface. Cement laitance or old coatings must be removed mechanically. It may be necessary to clean oil- or grease-stained concrete by burning with a torch and/or applying a special grease remover. Priming E 720 EMC should be applied onto the prepared surface with a soft brush or primer pump, ponding should be prevented, and it should be allowed to dry (2 – 4 hours under normal conditions). If the absorbency of the substrate to be treated is high, E 720 EMC should be applied diluted with clean water at a ratio of 1:5 for the first coat and 1:3 for the second coat. On sound concrete surfaces, a single coat diluted at 1:3 is sufficient. If application on different substrates is involved, please consult Dolphinfix for dilution ratios and application techniques. E 720 EMC should not be applied to surfaces with a temperature below +10°C. The surface must be dry, and the relative humidity must be below 70%. Insufficient drying time, low temperature, and/or high humidity may affect film formation, preventing it from completely covering the surface. Mixing The material must be mixed with clean water at a ratio of 23% (5.75 liters per 25 kg bag). During the mixing process, a paddle mixer attached to a drill or a pump approved by Dolphinfix must be used. When mixing with a paddle, the mixing time should not be less than 2 minutes. The mixed material must be used within 30 minutes, and the material temperature must be between +5°C and +20°C. Excessive cooling or heating of the dry material prior to use may affect the flow properties of the mixture. Application The mixed material is poured by spreading it onto the surface. Air bubbles trapped inside the material are easily released by passing over the material with a steel trowel or a spiked roller. Semi-hardened material can be easily shaped or cut, allowing desired corrections to be made. Floor Series products should not be applied to surfaces colder than +10°C. The floor must be protected against frost for 48 hours following the application. The relative humidity of the ambient air should be below 70%. Gentle ventilation is recommended during and after application, but dehumidifiers should not be used during the first two days period. The use of curing membranes is not required. Following the application of Floor – Self 200, structural and expansion joints as well as cracks that may continue to move must be transferred onto the new surface as joints. POINTS TO NOTE •Do not apply at temperatures below +5°C and above +35°C. •In exterior applications, in areas with a risk of freezing, the surface must be protected from sun, wind, rain or frost for the first 24 hours. •The working and reaction times of cement-based systems are affected by ambient and substrate temperatures and the relative humidity of the air. At low temperatures, hydration slows down, which extends the pot life and working time. High temperatures accelerate hydration and correspondingly shorten the times stated above. For the material to complete its setting, the ambient and substrate temperatures must not drop below the minimum allowed temperature. CONSUMPTION Depends on the surface to be applied. Dry material consumption is 1.5 kg/m² for 1 mm thickness. PACKAGING 25 kg kraft bag SHELF LIFE 6 months from the production date under suitable storage conditions. STORAGE CONDITIONS Store in unopened original packaging in a cool, dry environment, protected from frost. Do not stack more than 8 bags on top of each other.
CategoryFlooring Solutions › Self-Leveling Screed
KG25 KG Kraft Bag
OptionPiece (1 Piece), Pallet (64 Piece Kraft Bag)
Technical data sheetTDS.pdf
VAT rate%20
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.

Log in, you can write a review if you have purchased this product.

There are no reviews for this product yet.

Similar Products

PAR 721 – Screed Primer for Glossy Surfaces
PAR 721 – Screed Primer for Glossy Surfaces

DESCRIPTION: PAR 721 is a single-component, acrylic-based, water-based, ready-to-use primer material developed for glossy surfaces; it dulls the surface gloss, increases adhesion and improves the workability of the material to be applied over it.

At least889,90 ₺