PRODUCT INFORMATION ; DESCRIPTION: FLX 1250 is a cement-based, high-performance, S1-class flexible, versatile tile adhesive with reduced slip and extended open time. AREAS OF USE • In tile and ceramic wall and floor coverings, • In dry and wet areas, •In water tanks, • In pools, saunas, and Turkish baths •In mosaic, stone, tile, granite and terracotta ceramics, • For large-sized ceramics and slabs, • As a thin layer on lightweight construction boards, • Due to its high degree of deformability properties (balconies, terraces) PRODUCT FEATURES AND ADVANTAGES • Easily applied horizontally and vertically, non-slip, does not cause fatigue. • Resistant to severe weather conditions, • High adhesion properties, deformable, • Waterproof, resistant to frost and constant temperatures (up to +80 °C), • S1 class flexibility • Long open time, TECHNICAL SPECIFICATIONS Appearance / Color: Powder / Gray and White Application Temperature: (+5°C) – (+35°C) Pot life: 5 hours Slip: ≤0.5 mm Open time: At least 30 min, then ≥0.5 N/mm² Initial Tensile Adhesion Strength: ≥1 N/Mm² After immersion in water : ≥1 N/mm² After thermal aging: ≥1 N/mm² After freeze-thaw cycle: ≥ 1 N/mm² Flexibility (EN 12002: ≥ 2.5 mm – S1 Flexible Temperature Resistance: (-40°C) – (+80°C) Reaction to Fire: A2 Hazardous substances: See the safety data sheet. Typical values: obtained as a result of experiments conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten the durations, low temperatures prolong them. APPLICATION METHOD Surface Preparation: The application surface must be sound, free of anti-adhesive agents, dry, dust-free, and clean. The surface must be thoroughly cleaned of all kinds of oil, grease, rust, and paraffin residues that reduce adhesion, and there must be no loose particles on the surface. The floor to be applied must be damp, with no standing water. The use of a primer is recommended on water-absorbent surfaces and exposed concrete. If the surface temperature to be applied is above +30 °C, the surface must definitely be dampened. MIXING: Pour the specified amount of clean water into a clean bucket. Empty half of the 25 Kg. FLX 1250 into it and start mixing with a mixer at low speed. Add the entire remainder and mix until the mortar becomes lump-free and homogeneous, and leave it to rest for 5-6 minutes to mature. Then mix for another 1-2 minutes before use. Spread the adhesive over the entire surface and apply at a uniform thickness by combing with a notched trowel. Checking the surface smoothness, the cladding materials are tapped with the aid of a rubber mallet to ensure proper seating and adhesion. Joint filler application should be carried out at least 24 hours later. PACKAGING: 25 Kg Kraft Bag WARNINGS: Do not use material left in the container that has exceeded its pot life or has formed a skin. This material must be discarded. Prepare only as much material as you can use. Tools should be cleaned while the mortar is wet. It must definitely be protected in environments below (+) 5°C and above (+) 35°C. The surroundings must be covered with nylon. Precautions must be taken against frost and sudden water loss. STORAGE: It should be stored within the range of +5 °C and 30°C. It must be protected from frost, moisture, and direct sunlight. SHELF LIFE: 12 months from the production date in its original, undamaged and unopened packaging, provided storage conditions are observed.
Category
Construction Chemicals › Ceramic Tile Adhesive
Color
Gray, White
KG
25 KG Kraft Bag
Option
Piece (1 Piece), Pallet (64 Piece Kraft Bag)
VAT rate
%20
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.