PRODUCT INFORMATION ; DESCRIPTION: D-TH K 1102 is a cement-based, hydraulic-binder thick repair mortar. AREAS OF USE • Autoclaved Aerated Concrete (AAC), •Brick, •Raw concrete, • In plaster repairs, • In broken corners, • In chamfer creation, PRODUCT FEATURES •Easy workability, •Does not shrink or crack, •High adhesion, •Can be applied indoors and outdoors, • D- TH K 1102 is a fine repair mortar that becomes ready for use when mixed with water. • D- TH K 1102 is very easy to work with and has high-performance properties, •Resistant to all climatic conditions after hardening. TECHNICAL SPECIFICATIONS Material composition: Contains special cements, fibers, polymers and mineral fillers. Color: Gray *Compressive strength (TS EN 12190)28. Days: ≥15 N/Mm² Adhesion (pull-off) strength (TS EN 1542) (to concrete, 28 days): >0.8 N/mm² Chloride ion content: ≤ 0.05% Capillary water absorption (TS EN 13057): <0.5 kg.m⁻².h⁻⁰·⁵ Application thickness: Max 5 mm Temperature of the substrate to be applied: +5°C to +30°C Service temperature: -20°C to +40°C Pot life (+20°C): 30 min. Walkable after (+20°C): 24 hours Full curing time (+20°C): 28 days Typical values: obtained as a result of experiments conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten the durations, low temperatures prolong them. APPLICATION METHOD Surface Preparation: Care must be taken to ensure that the cement-based surfaces of structures to be repaired are sound, load-bearing, dust-free, and clean. The surface must be thoroughly cleaned of all kinds of oil, rust, grease, and paraffin residues that would weaken adhesion. The chipped The edges of the surface should be cut as vertically as possible, rust on the reinforcement must be cleaned, and new reinforcement should be added if necessary. If there is water leakage on the surface, it should be drained or plugged with a suitable plugging compound. The application surface must be saturated with water, but no free water should remain on the surface. Mixing: The appropriate amount of water is poured into a clean mixing bucket using a measuring cup. D- TH K 1102 is added slowly and mixed for 4 minutes with a 400-600 rpm mixer until a homogeneous and lump-free mixture is obtained. After allowing it to rest for approximately 4 minutes and mixing again for 30 seconds, the material becomes ready for use. MIXING RATIOS FOR 1 KG OF POWDER D- TH K 1102 FOR 25 KG BAG MIXING WATER AMOUNT 0,14 lt – 0,16 lt 3,50 lt – 4,0 lt MIXING DENSITY 2,10 kg/lt Application The prepared mortar is applied to the surface by trowel or spraying, with a thickness between 5 mm and 40 mm in a single layer. In thicker applications, after the first layer dries, the second layer is applied to the surface in the same way. In cases where a smooth surface finish is desired, it is waited for the mortar to lose its bleed water, and the surface is finished with a steel or wooden trowel by sprinkling water on the mortar that has lost its water using a plasterer's brush. Large surfaces exposed to the atmosphere, especially hot, dry, or windy environments, must be protected against rapid evaporation for 24-48 hours with wet burlap, water, or special curing agents. PACKAGING 25 kg polyethylene-reinforced kraft bag. CONSUMPTION 1.75 kg/m² of powder product for 1 mm thickness SHELF LIFE 12 months from the production date under suitable storage conditions. Opened packages must be stored under suitable conditions and used within one week.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: THM 1105 is a very easy-to-use top-coat satin plaster and leveling putty based on cement, supported with special polymers and micronized aggregates.
DESCRIPTION: D-TH S1 1104 is a cement-based, high-polymer and fiber-modified, silica-fume, performance-enhanced structural fine repair and leveling mortar.