PRODUCT INFORMATION ; DESCRIPTION: D-TH G 1106 is a cement-based, high-performance, expandable special filling mortar. AREAS OF USE •For filling all kinds of voids on the existing surface prior to waterproofing due to its early strength and high water resistance, •For filling tie-rod and formwork spacer holes due to its expansive property, •For patching core sample holes taken from bare concrete, •In tie-rod holes, PRODUCT FEATURES •Due to its plastic consistency, it stays easily in vertical and horizontal voids and holes, •Does not shrink or crack, •Adheres perfectly due to its high adhesion strength, •Hardens quickly, •Provides impermeability. •Resistant to all climatic conditions after hardening. TECHNICAL SPECIFICATIONS Material composition: Contains special cements, fibers, polymers and mineral fillers. Color: Gray Compressive Strength (TS EN 12190) 1. Days 15 N/Mm² 7. Days 40 N/Mm² 28. Days 50 N/Mm² Adhesion (Tensile) Strength (TS EN 1542) (To concrete 28 days): ≥2 N/mm² Chloride ion content: ≤ 0.05% Capillary water absorption (TS EN 13057): <0.5 kg.m⁻².h⁻⁰·⁵ Application thickness: Max 5 mm Temperature of the substrate to be applied: +5°C to +30°C Service temperature: -20°C to +40°C Pot life (+20°C): 30 min. Walkable after (+20°C): 24 hours Full curing time (+20°C): 28 days Typical values: Obtained as a result of tests performed on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten durations, low temperatures prolong them. APPLICATION METHOD Surface Preparation: Care must be taken to ensure that the cement-based surfaces of structures to be repaired are sound, load-bearing, dust-free, and clean. The surface must be thoroughly cleaned of all kinds of oil, rust, grease, and paraffin residues that would weaken adhesion. The edges of the surface formed by chipping must be cut as vertically as possible, rust on the reinforcement must be cleaned, and new reinforcement must be added if necessary. If there is water leakage on the surface, it should be drained or plugged with a suitable plugging mortar. The application surface must be saturated with water, but no free water should remain on the surface. Mixing The appropriate amount of water is poured into a clean mixing bucket using a measuring scale. D- TH G 1106 is added slowly and mixed for 4 minutes with a 400-600 rpm mixer until a homogeneous and lump-free mixture is obtained. After resting for approximately 4 minutes and mixing again for 30 seconds, the material is ready for use. MIXING RATIOS FOR 1 KG OF POWDER D- TH G 1106 FOR 25 KG BAG MIXING WATER AMOUNT 0.13 l – 0.15 l / 3.25 l – 3.80 l MIX DENSITY 1.90 kg/l Application The prepared mortar is applied to the surface by trowel or spraying, with a thickness between 5 mm and 40 mm in a single layer. In thicker applications, after the first layer dries, the second layer is applied to the surface in the same way. In cases where a smooth surface finish is desired, it is waited for the mortar to lose its bleed water, and the surface is finished with a steel or wooden trowel by sprinkling water on the mortar that has lost its water using a plasterer's brush. Large surfaces exposed to the atmosphere, especially hot, dry, or windy environments, must be protected against rapid evaporation for 24-48 hours with wet burlap, water, or special curing agents. PACKAGING 25 kg kraft bag. CONSUMPTION 1.75 kg/m² of powder product for 1 mm thickness
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: D-TH S1 1104 is a cement-based, high-polymer and fiber-modified, silica-fume, performance-enhanced structural fine repair and leveling mortar.
DESCRIPTION: THM 1105 is a very easy-to-use top-coat satin plaster and leveling putty based on cement, supported with special polymers and micronized aggregates.