PRODUCT INFORMATION ; DESCRIPTION: HTH 1107 is a cement-based, special polymer-modified, highly water-resistant hydrophobic waterproofing mortar. AREAS OF USE •In all indoor and exterior areas of buildings, •On gross concrete and cement-based plasters, •For surface repair and obtaining a smooth surface before negative and positive waterproofing applications, •In the repair of edges and corners, •In chamfer applications, PRODUCT FEATURES AND ADVANTAGES •High adhesion properties. •Does not shrink. •Provides smooth, even surfaces, •High resistance to water. •Can be applied indoors and outdoors. •Resistant to weather conditions and frost. •Has water vapor permeability. •Flexible. TECHNICAL SPECIFICATIONS Structure of the Material: Contains special cements, synthetic additives, and mineral fillers. Color: White Compressive Strength (TS EN 12190): ≥25 N/mm² (28 days) Flexural Strength (28 days) (TS EN 196): ≥3.5 N/mm² (28 days) Adhesion (Tensile) Strength (TS EN 1542) (on concrete 28 days): ≥1.5 N/mm² Capillary Water Absorption (TS EN 13057): ≤0.5 kg.m¯².h¯⁰∙⁵ Application Thickness: Maximum 5 mm Substrate Temperature to be Applied: +5°C +30°C Service Temperature: -20°C +40°C Pot Life (+20°C): 30 min. Walkability Time (+20°C): 24 hours Full Curing Time (+20°C): 28 days Typical values: Obtained as a result of tests conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten times, low temperatures prolong them. APPLICATION METHOD Surface Preparation: Care must be taken to ensure that the cement-based surfaces of buildings to be repaired or plastered are sound, load-bearing, dust-free, and clean. The surface must be thoroughly cleaned of all kinds of oil, rust, grease, and paraffin residues that would weaken adhesion. The edges of the surface formed by breaking should be cut as vertically as possible, the rust on the reinforcement should be cleaned, and new reinforcement should be added if necessary. If there is water leakage on the surface, it should be drained or plugged with a suitable water plug. The application surface should be saturated with water, but no free water should remain on the surface. Mixing: The appropriate amount of water is poured into a clean mixing bucket using a measuring scale. HTH 1107 is added slowly and mixed for 4 minutes with a 400-600 rpm mixer until a homogeneous and lump-free mixture is obtained. After letting it rest for approximately 4 minutes and mixing it again for 30 seconds, the material is ready for use. MIXING RATIOS FOR 1 KG OF HTH 1107 FOR 25 KG BAG MIXING WATER AMOUNT 0.20 lt – 0.24 lt 5.0 lt – 6.00 lt MIXING DENSITY 1.70 kg/lt APPLICATION The prepared mortar is applied to the surface with a trowel such that the thickness in a single layer is a maximum of 5 mm. In thicker applications, after the first layer dries, the second layer is applied to the surface in the same way. In cases where a smooth surface finish is desired, the mortar is allowed to draw its water, and water is sprinkled onto the water-drawn mortar using a plasterer's brush, and the surface is finished with a steel or wooden trowel. Large surfaces exposed to the atmosphere, especially hot, dry, or windy environments, must be protected against rapid evaporation for 24-48 hours using wet burlap, water, or special curing agents. PACKAGING 25 kg kraft bag. CONSUMPTION 1.5 kg/m2 of dry product for 1 mm thickness SHELF LIFE 12 months from the date of production under suitable storage conditions. Opened packages should be used within one week by storing them under suitable storage conditions.
Category
Landscape and Green Roof › Landscape Waterproofing
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
With its unique production technology, it is manufactured in 3 layers with top and bottom POLYPROPYLENE (PP) intermediate layers made of POLYETHYLENE (PE) raw material. Dolphinfix waterproofing membranes are technical textile water insulation products resistant to high water pressure.
DESCRIPTION: PUR 203 is a single-component, ready-to-use, liquid-applied, upgraded polyurethane waterproofing coating that remains permanently elastic and cures by reacting with moisture in the air.