PRODUCT INFORMATION ; DESCRIPTION: D-TH S 1103 is a cement-based, fiber- and polymer-modified, corrosion-resistant, silica-fume thixotropic structural repair mortar. AREAS OF USE •In structural concrete repairs, •In joints, in chamfer making, •In tie-rod holes and core voids, •In coatings for the purpose of protecting concretes against the effects of sulfate and chlorine, PRODUCT FEATURES •Does not require a primer. •Does not shrink (shrinkage-free) •Resistant to chlorine, sulfate and oils. •Gains strength rapidly. •Can be applied indoors and outdoors. •Shows high resistance to water. TECHNICAL SPECIFICATIONS Material composition: Contains special cements, fibers, polymers and mineral fillers. Color: Gray Compressive strength (TS EN 12190): 1. Days 14 N/Mm² 7. Days 37 N/Mm² 28. Days 47 N/Mm² Flexural Strength (28 days) (TS EN 196): 7 N/mm² Adhesion (Tensile) Strength (TS EN 1542) (To concrete 28 days): >2,0 N/mm² Modulus of elasticity (28 days): >20,000 N/mm² Capillary water absorption (TS EN 13057): <0.5 kg.m⁻².h⁻⁰·⁵ Application Thickness: Min 5 mm Maximum 50 mm Temperature of the substrate to be applied: +5°C to +30°C Service temperature: -20°C to +40°C Pot life (+20°C): 30 min. Walkable after (+20°C): 24 hours Full curing time (+20°C): 28 days Typical values: obtained as a result of experiments conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten the durations, low temperatures prolong them. APPLICATION METHOD Surface Preparation: Care must be taken to ensure that the cement-based surfaces of the structures to be repaired are sound, load-bearing, dust-free and clean. The surface must be thoroughly cleaned of all kinds of oil, rust, grease and paraffin residues that would weaken the adhesion. The edges of the chipped surface should be cut as vertically as possible, rust on the reinforcement should be cleaned, and new reinforcement should be added if necessary. If there is water flow on the surface, it should be drained or plugged with a suitable plugging mortar. The application surface should be saturated with water, but there should be no free standing water on the surface. Mixing: The appropriate amount of water is poured into a clean mixing bucket using a measuring scale. D- TH S 1103 is added slowly and mixed for 4 minutes with a 400-600 rpm mixer until a homogeneous and lump-free mixture is obtained. After allowing it to rest for approximately 4 minutes and mixing again for 30 seconds, the material is ready for use. MIXING RATIOS FOR 1 KG OF D- TH S POWDER FOR 25 KG BAG MIXING WATER AMOUNT 0.136 lt – 0.14 lt 3.4 lt – 3.5 lt MIX DENSITY 2.30 kg/l Application The prepared mortar is applied to the surface by trowel or spraying, with a thickness between 5 mm and 40 mm in a single layer. In thicker applications, after the first layer dries, the second layer is applied to the surface in the same manner. In cases where a smooth surface finish is desired, it is waited for the mortar to draw its water, and by sprinkling water on the mortar that has drawn its water using a plasterer's brush, the surface is finished with a steel or wooden trowel. Large surfaces exposed to the atmosphere, especially hot, dry, or windy environments, should be protected against rapid evaporation for 24-48 hours using wet burlap, water, or special curing compounds. PACKAGING 25 kg polyethylene-reinforced kraft bag. CONSUMPTION 2 kg/m2 powder product for 1 mm thickness SHELF LIFE 12 months from the production date under suitable storage conditions. Opened packages must be stored under suitable conditions and used within one week.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: THM 1105 is a very easy-to-use top-coat satin plaster and leveling putty based on cement, supported with special polymers and micronized aggregates.