DESCRIPTION: DTY 1701 is a cement-based, polymer-modified, fiber-reinforced plaster mortar developed for plastering over thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.).
PRODUCT INFORMATION ; DESCRIPTION: DTY 1701 is a cement-based, polymer-modified, fiber-reinforced plaster mortar developed for plastering over thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.). AREAS OF USE; •For rendering all thermal insulation boards (EPS, XPS, rock wool, thermal and acoustic insulation felt, etc.), •In horizontal, vertical and overhead plastering applications, •In architectural structures where thermal insulation is applied, •Indoors and outdoors, •For rendering on concrete, aerated concrete, gross concrete, and hollow-core clay block insulation foam, •Used as a general render apart from external thermal insulation composite systems (ETICS). PRODUCT SPECIFICATIONS; •Easy application property, •Weather resistant (after curing). •Comfort of professional application. •Easy and long workability. •Vapor permeable. •Paint can be applied directly onto it. APPLICATION INFORMATION; Surface Preparation : The application surface must be sound, dry, dust-free, and clean, preventing any reduction in adhesion. The surface must be thoroughly cleaned of all kinds of oil, grease, rust, and paraffin residues that would reduce adhesion, and there must be no loose particles on the surface. If the surface temperature to be applied is above +30 °C, the surface must definitely be dampened. Irregularities on the surface must be repaired with the appropriate D- TH repair mortars. Pre-Application : After the thermal insulation boards are bonded and the curing time has elapsed, the gaps that may occur between the boards are filled with board pieces cut to the appropriate size, and the doweling process is carried out. The doweling process is performed such that 6 dowels fall per 1 m². As the floors get higher, the number of dowels must be increased. Ensure that the head of the dowels is neither too protruding nor too recessed. Mixing : Put a portion of 6 – 7 lt. of clean water into a clean bucket. While slowly pouring 25 Kg of DTS 1701 onto it, start mixing with a mixer at a low speed. Add the remaining water and leave the mortar to rest for 3-4 minutes until it becomes lump-free and homogeneous. Then, mix for at least 2 more minutes before use. Application : It is applied onto the thermal insulation boards in a thickness of 4 mm using a 10×10 mm notched steel trowel. Alkali-resistant reinforcing mesh (160 gr/m2) is overlapped by 10 cm and embedded 1-1,5 mm close to the exterior facade with a trowel before the render dries, and the render surface is smoothed. In areas with sudden cross-section changes such as doors and windows, additional mesh reinforcement and DTS 1701 application must be carried out. It is recommended to prefer meshed corner profiles for profile applications made to ensure that building edges come out properly. During application or during curing, the ambient temperature and surface temperature must be between at least (+)5 °C and at most (+)30 °C. WARNINGS : It must definitely be protected in environments below (+) 5 °C and above (+) 35 °C. Its surroundings must be covered with nylon. Precautions must be taken against frost and sudden water loss. PACKAGING: 25 Kg Kraft Bag SHELF LIFE: 12 months from the production date in its original, undamaged and unopened packaging, provided storage conditions are observed. CONSUMPTION AND WATER AMOUNT : 1 m² Powder Consumption 4,5 – 5,5 Kg 5,5 – 6,5 Kg MIXING WATER AMOUNT 6 – 7 Lt./25 Kg STORAGE CONDITIONS: Store between +5°C and 30°C. Protect from frost, moisture and direct sunlight. For the product's technical specifications and other information, please download the TDS document.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: DTY 1700 is a cement-based, polymer-modified adhesive mortar used for bonding thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.) to the surface to be insulated.
DESCRIPTION: DTDS 1703 is a cement-based, polymer-modified, fiber-reinforced, water-repellent fine-patterned coating material used as an exterior facade top-coat plaster.
DESCRIPTION: Therm 005 roof & terrace, Elastomeric resin-based, modified through special processes with various products possessing high insulation properties containing trapped air, lightweight volcanic craters, and vacuumed natural spheres turned into bubbles by expanding silicate melted at 2400 °C...
DESCRIPTION: Therm +3 facade coating is based on acrylic copolymer and specially modified elastomeric resin. It is a water-based, ready-to-use, brush-applied thermal and waterproofing material.