DESCRIPTION: MicroFloor MB 1003 MFB is a cement-based flowable micro-concrete (microtopping) floor coating mortar that can be applied by hand or pump, consisting of special cements, quality mineral fillers, high-performance polymer binders and new-generation functional chemical admixtures.
PRODUCT INFORMATION ; DESCRIPTION: MicroFloor MB 1003 MFB is a cement-based, flowable micro-concrete (microtopping) floor coating mortar consisting of special cements, qualified mineral fillers, high-performance polymeric binders, and next-generation functional chemical additives, which can be applied manually or by pump. It is formulated to be applied in thicknesses ranging from 4 mm to 30 mm in a single coat. It is an eco-friendly system with a low VOC value, containing high-performance plasticizers and superplasticizers. AREAS OF USE •In new construction projects and floor renovations of existing structures, •As an aesthetic, jointless, and seamless final coat flooring on indoor and outdoor floors, •In leveling, structurally correcting, and smoothing existing concrete floors, •In hospitals, food production, processing, and storage facilities requiring high hygiene and mechanical strength, •Used as a decorative flooring solution in residences, offices, showrooms, hotels, stores, and qualified commercial areas. PRODUCT FEATURES •Excellent Self-Leveling Property: With its self-leveling performance, it creates extremely smooth and leveled surfaces with minimum labor. •Fast Curing: Allows pedestrian traffic 2 – 4 hours after application under normal ambient conditions, saving time in projects. •High Mechanical Strength: Possesses high early and final compressive and flexural strengths. •Low Shrinkage: Minimizes the risk of cracking thanks to its minimum shrinkage property. •Protein and Casein Free: Since it does not contain organic-based casein or protein derivatives in its structure, it does not allow the formation of mold, fungi, and bacteria; ideal for sterile areas. •Decorative Variety: Can be produced in desired colors according to project demands. HYDRATION AND LIQUID ABSORPTION PROTECTION PROTOCOL (POLISHING / SEALING) IMPORTANT TECHNICAL NOTE: MicroFloor MB 1003 MFB has a cement-based matrix structure. Due to the nature of cement, microscopic voids (micro-pores) occur on the surface during the hydration (reaction and setting) process due to the evaporation of water in the mortar.During the service stage after curing, in order to completely prevent the absorption of liquids (water, oil, coffee, chemicals, etc.) that may be spilled on the surface by these micro-pores, stain formation, and discoloration; it is mandatory to seal the surface with a suitable protective coating or polish (topcoat/sealer) system. The polish layer preserves the color vibrancy of the system permanently while providing the surface with maximum hygiene, stain resistance, and easy cleanability. TECHNICAL SPECIFICATIONS •Compressive Strength: > 30 N/mm² •Flexural Strength: > 7 N/mm² •Adhesion to Concrete (SS 92 35 07): > 2 N/mm² •Free shrinkage: 0.04 – 0.06% •MINTEC ring test (SS 92 35 19): 145 – 155 mm •Pot life (ready-mix usable time): 15 – 20 minutes •pH value: Approximately 11 •Hardening time (foot traffic): 2 – 4 hours •Application Thickness: 4 – 15 mm (Layer thickness on lightweight concrete floors should be limited to 6 – 10 mm) •Dry material consumption: 1.7 kg/m² (for 1 mm thickness) (depends on the surface to be applied) APPLICATION METHODOLOGY A. Surface Preparation •It must be determined that the substrate to be applied is hard, sound, load-bearing, and dry. •The surface must be cleaned of all foreign substances that would weaken adhesion, such as cement slurry, weak layers, dust, paint, oil, grease, and epoxy residues, by mechanical methods (shot-blasting, milling, or grinding). •Deep stains impregnated with oil or grease must be burned off with a torch or cleaned with special industrial degreasers. Before application, all dust on the surface must be vacuumed with a vacuum cleaner. B. Priming •E 720 EMC primer must be applied homogeneously to the prepared surface with a soft brush, roller, or primer pump without allowing puddling. •The drying time of the primer is 2 – 4 hours under normal conditions. •On high-absorbency floors: E 720 EMC primer must be applied in double coats, diluted with water at a ratio of 1:5 (Primer:Water) for the 1st coat and 1:3 for the 2nd coat. • On sound concrete substrates: a single-layer application diluted at a ratio of 1:3 is sufficient. • For different and special substrate types, the Dolphinfix technical support department must be consulted regarding technical dilution ratios and application methodology. •Primer application must not be carried out if the substrate and ambient temperature are below +10 °C, and the ambient relative humidity is above 70%. Insufficient drying and adverse ambient conditions may prevent the primer from forming a film layer. C. Mixing • A 25 kg bag of MicroFloor MB 1003 MFB must be mixed with 20% (5.00 liters) of clean and cold water. • The mixing process must be carried out using a suitable paddle attached to a low-speed mixer or with integrated pumping equipment approved by Dolphinfix. • The mixing time with the paddle must be at least 2 minutes continuously. After obtaining a homogeneous mixture, the material must be consumed within 20 minutes. • During mixing, the material temperature must be between +5 °C and +20 °C. Exposure of the dry powdery material to excessively hot or cold environments prior to application may directly affect the fluidity and leveling performance of the product. D. Application •The homogeneously mixed material is poured onto the surface in a continuous line. • After pouring the material, it must be spread with a notched rake or a steel trowel, and then rolled in cross directions with a spike roller to remove air bubbles on the surface and ensure the material knits together. • Semi-hardened material can be easily shaped or cut; necessary local corrections can be made at this stage. • During application and for the first 48 hours thereafter, the floor and ambient temperature must not drop below +10 °C, and the floor must be protected against frost. The ambient relative humidity must be kept below 70%. • Mild ventilation should be provided in the environment after application, but dehumidifiers or aggressive air currents (air circulation) that would rapidly dry the surface must be prevented for the first 2 days. The use of a curing membrane is not required. • Moving joints, cracks, and dilatation lines of the main structure must be transferred precisely as joints onto the MicroFloor coating. WATER AND CHEMICAL RESISTANCE • Water Resistance: Pouring water on fully hardened MicroFloor series products does not damage the material. However, continuous and prolonged submersion of the material in water may lead to a loss of mechanical resistance. Following the removal of water and a 24-hour drying process, the material regains its original strength values. • Chemical Resistance: The chemical resistance of the product is similar in nature to standard high-quality concrete. In industrial areas where there is a risk of continuous exposure to aggressive chemicals, the surface must be protected with suitable chemically resistant coatings. LIMITATIONS AND POINTS TO NOTE • Application is strictly not recommended in cases where the floor and ambient temperature are below +5 °C and above +35 °C. • In outdoor applications, the surface must be protected from direct sunlight, wind, heavy rain, and frost for the first 24 hours. • The workability and reaction times of cement-based systems are directly affected by ambient and substrate temperatures. At low temperatures, hydration slows down; this extends the pot life (pan life) but delays the setting time. At high temperatures, hydration accelerates, which shortens the working time. • Application thickness limits (4 – 30 mm) must be strictly complied with. In order to optimize consumption on surfaces with excessive elevation differences, leveling should be carried out using MicroFloor RM 1000 MRM repair mortar prior to application. CLEANING OF TOOLS All tools and equipment used immediately after application must be washed with water. Hardened material can only be cleaned from the surface by mechanical methods. PACKAGING, STORAGE AND SHELF LIFE •Packaging: 25 kg kraft bag. •Storage: Store in unopened original packaging in a cool, dry and moisture-free environment, protected from frost. Stack a maximum of 8 bags on top of each other. •Shelf life: 6 months from the production date under the specified suitable storage conditions.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: MicroFloor RM 1000 MRM is a high-strength, self-spreading (flowable) floor repair and filling mortar developed with a combination of special cements, high-quality mineral fillers, polymer binders and new-generation functional chemical admixtures.
DESCRIPTION: MicroFloor MB 1004 MFB is formulated with a combination of special cements, high-purity mineral fillers, functional polymer binders and new generation chemical additives for floors exposed to industrial, parking and heavy traffic loads, applied by hand or pump, cement-based a...