🌐 English ▾
📞 Customer Line 24/7539 303 00 72
🌐 English ▾
Home ›Construction Chemicals›Repair Mortar ›D TH S 1104 THS – Structural Fine Repair Mortar

D TH S 1104 THS – Structural Fine Repair Mortar

Category: Repair Mortar
386,10 ₺
Prices do not include %20 VAT; it is added at checkout.

DESCRIPTION: D-TH S1 1104 is a cement-based, high-polymer and fiber-modified, silica-fume, performance-enhanced structural fine repair and leveling mortar.

KG:
Option:
📞 Request a quote for bulk / pallet purchases
🚚 Fast Shipping
🛡️ Secure Payment
↩️ Easy Returns
PRODUCT INFORMATION ; DESCRIPTION: D-TH S1 1104 is a cement-based, high-polymer and fiber-modified, silica-fume, performance-enhanced structural fine repair and leveling mortar. AREAS OF USE • For concrete surface repairs on interior and exterior facades, •In precast and raw concrete surface corrections, •In engineering structures such as highways, dams, and metros, •In all kinds of industrial reinforced concrete structures, PRODUCT FEATURES •High adhesion. •Does not shrink (shrinkage-free) • To obtain a smooth, even surface, •Resistant to chlorine, sulfate and oils. •It has a thixotropic structure. •Can be applied indoors and outdoors. •Resistant to weather conditions and frost. TECHNICAL SPECIFICATIONS Material Composition: Contains special cements, fibers, synthetic additives and mineral fillers. Color: Gray Compressive strength (TS EN 12190): ≥32 N/Mm² (28 Days) Flexural strength (28 days) (TS EN 196): ≥4 N/mm² (28 days) Adhesion (pull-off) strength (TS EN 1542) (to concrete, 28 days): ≥1.5 N/mm² *Modulus of Elasticity (28 Days): ≥20.000 N/Mm² Capillary water absorption (TS EN 13057): ≤0.5 kg.m⁻².h⁻⁰·⁵ Application Thickness: 10 mm (in a single coat) Temperature of the substrate to be applied: +5°C to +30°C Service Temperature -20°C +40°C Pot life (+20°C): 30 min. Walkable after (+20°C): 24 hours Full curing time (+20°C): 28 days Typical values: obtained as a result of experiments conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten the durations, low temperatures prolong them. APPLICATION METHOD Surface Preparation: Ensure that the cement-based surfaces of structures to be repaired are sound, load-bearing, dust-free and clean attention must be paid. The surface must be thoroughly cleaned of all oil, rust, grease, and paraffin residues that would weaken adhesion. The edges of the surface created by chipping should be cut as vertically as possible, the rust on the reinforcement must be cleaned, and new reinforcement should be added if necessary. If there is water flow on the surface, it must be drained or plugged with a suitable plug. The application surface must be saturated with water, but no free water should remain on the surface. Mixing: The appropriate amount of water is poured into a clean mixing bucket with the help of a measuring scale. D- TH S1 1104 is added slowly and mixed for 4 minutes with a 400-600 rpm mixer until a homogeneous and lump-free mixture is obtained. After resting for approximately 4 minutes and mixing again for 30 seconds, the material is ready for use. MIXING RATIOS D- TH S1 1104 FOR 1 KG POWDER FOR 25 KG BAG MIXING WATER AMOUNT 0.18 lt – 0.20 lt 4.5 lt – 5.0 lt MIXING DENSITY 1.75 kg/lt Application The prepared mortar is applied to the surface by trowel or by spraying so that the thickness in a single coat is maximum 10 mm. In thicker applications, after the first coat dries, the second coat is applied to the surface in the same way. In cases where a smooth surface finish is desired, it is waited for the mortar to draw its water, and by sprinkling water on the mortar that has drawn its water with a plasterer's brush, the surface is finished with a steel or wooden trowel. Large surfaces open to the atmosphere, especially hot, dry or windy environments, should be protected against rapid evaporation for 24-48 hours with wet burlap, water or special curing agents. PACKAGING 25 kg polyethylene-reinforced kraft bag. CONSUMPTION 1.8 kg/m² of powder product for 1 mm thickness SHELF LIFE 12 months from the production date under suitable storage conditions. Opened packages must be stored under suitable conditions and used within one week.
CategoryConstruction Chemicals › Repair Mortar
KG25 KG Kraft Bag
OptionPiece (1 Piece), Pallet (64 Piece Kraft Bag)
Technical data sheetTDS.pdf
VAT rate%20
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.

Log in, you can write a review if you have purchased this product.

There are no reviews for this product yet.

Similar Products