PRODUCT INFORMATION ; DESCRIPTION: D-TH D 1101 is a cement-based, high-performance fine repair and leveling mortar. AREAS OF USE •In interior and exterior areas, •In dry, damp, wet, and underwater areas, •Especially for thin-layer leveling on rough-textured concrete, •Precast elements, •In the repair of concrete form elements, •As a base coat to achieve a smooth surface in full-covering putty application on porous concrete top surfaces, PRODUCT FEATURES AND ADVANTAGES •It is a dry mortar prepared with mineral-based fillers and reinforced with silica fume, •It is a pre-blended, mineral-based dry mortar/putty mortar that is ready for use when mixed with water and hardens quickly hydraulically, •D- TH D 1101 is easy to apply and allows for smoothing. •Advantage of application up to 8 mm in a single layer •Hardens shrinkage-free and stress-free •Achieved high adhesion properties thanks to special polymer additives. •Resistant to all climatic conditions after hardening. TECHNICAL SPECIFICATIONS Material composition: Contains special cements, fibers, polymers and mineral fillers. Color: Gray Compressive Strength (TS EN 12190) 28th Day: ≥25 N/mm² Adhesion (pull-off) strength (TS EN 1542) (to concrete, 28 days): ≥1.5 N/mm² Chloride ion content: ≤ 0.05% Capillary water absorption (TS EN 13057): <0.5 kg.m⁻².h⁻⁰·⁵ Application thickness: Max 5 mm Temperature of the substrate to be applied: +5°C to +30°C Service temperature: -20°C to +40°C Pot life (+20°C): 30 min. Walkable after (+20°C): 24 hours Full curing time (+20°C): 28 days Typical values: obtained as a result of experiments conducted on 4x4x16 cm mortar prisms at +23°C and 50% relative humidity conditions. High temperatures shorten the durations, low temperatures prolong them. APPLICATION METHOD SURFACE PREPARATION Care must be taken to ensure that the cement-based surfaces of structures to be repaired are sound, load-bearing, dust-free, and clean. The surface must be thoroughly cleaned of all kinds of oil, rust, grease, and paraffin residues that would weaken adhesion. The edges of the surface created by chipping should be cut as vertically as possible, rust on the reinforcement must be cleaned, and new reinforcement should be added if necessary. If there is water leakage on the surface, it should be drained or plugged with a suitable plugging mortar. The application surface must be saturated with water, but no free water should remain on the surface. Mixing: The appropriate amount of water is poured into a clean mixing bucket with the help of a measuring scale. D- TH D 1101 is added slowly and mixed with a 400-600 rpm mixer for 4 minutes until a homogeneous and lump-free mixture is obtained. After resting for approximately 4 minutes and mixing again for 30 seconds, the material is ready for use. MIXING RATIOS FOR 1 KG OF D- TH D 1101 FOR 25 KG BAG MIXING WATER AMOUNT 0.13 l – 0.15 l / 3.25 l – 3.80 l MIX DENSITY 1.90 kg/l Application The prepared mortar is applied to the surface by trowel or spraying, with a thickness between 5 mm and 40 mm in a single layer. In thicker applications, after the first layer dries, the second layer is applied to the surface in the same way. In cases where a smooth surface finish is desired, it is waited for the mortar to lose its bleed water, and the surface is finished with a steel or wooden trowel by sprinkling water on the mortar that has lost its water using a plasterer's brush. Large surfaces exposed to the atmosphere, especially hot, dry, or windy environments, must be protected against rapid evaporation for 24-48 hours with wet burlap, water, or special curing agents. PACKAGING 25 kg polyethylene-reinforced kraft bag. CONSUMPTION 1.75 kg/m² of powder product for 1 mm thickness SHELF LIFE 12 months from the production date under suitable storage conditions. Opened packages must be stored under suitable conditions and used within one week.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: THM 1105 is a very easy-to-use top-coat satin plaster and leveling putty based on cement, supported with special polymers and micronized aggregates.