DESCRIPTION: DTY 1700 is a cement-based, polymer-modified adhesive mortar used for bonding thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.) to the surface to be insulated.
PRODUCT INFORMATION ; DESCRIPTION: DTY 1700 is a cement-based, polymer-modified adhesive mortar used for bonding thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.) to the surface to be insulated. AREAS OF USE; •On all mineral surfaces, •In the bonding of products such as EPS, XPS, rock wool, heat and sound insulation felt, etc. •In horizontal, vertical and overhead applications, •In architectural structures where thermal insulation is applied, •Indoors and outdoors, •On brick, autoclaved aerated concrete, exposed concrete and plastered surfaces, •Can be used as a general adhesive besides thermal insulation systems. PRODUCT FEATURES; • High bond strength. • Resistant to temperature and frost (after hardening). •Comfort of professional application. • Long-lasting. •Vapor permeable. APPLICATION METHOD; Surface Preparation : The application surface must be sound, dry, dust-free, clean, and free of substances that prevent adhesion. The surface must be thoroughly cleaned of all kinds of oil, grease, rust, and paraffin residues that would reduce adhesion, and there must be no loose particles on the surface. If the application surface temperature is above +30 °C, the surface must definitely be dampened. Surface defects must be repaired with the appropriate D- TH repair mortar. Mixing : Put a portion of 5.9-6.5 lt. of clean water into a clean bucket. While slowly pouring 25 Kg. DTY 1700 into it, start mixing at low speed with a mixer. Allow the mortar to rest for 3-4 minutes until it becomes lump-free and homogeneous. Then mix for at least 2 more minutes before use. CONSUMPTION AND WATER AMOUNT TABLE : 1 m² Powder Consumption 4 – 4.5 Kg 5.5 – 6.5 Kg MIXING WATER AMOUNT 6 – 7 Lt./25 Kg Application methods : Authorized institutions, primarily IZODER, recommend two methods. 1. Perimeter Method: Apply the mortar along the edges of the thermal insulation board using a trowel and place blobs of bonding mortar in the center. Fix it to the surface in this manner. (This is the method generally used on defective and old surfaces.) 2. Notched Trowel Method: We spread our mortar nicely on the surface of the thermal insulation board with a notched trowel and adhere the board to the surface. WARNINGS : Application made by forming blobs on the surface of the board is definitely not a correct application. Below (+) 5°C and must be protected in environments above (+) 35°C. It must be covered with nylon. Precautions must be taken against frost and sudden water loss. PACKAGING: 25 Kg Kraft Bag SHELF LIFE: 12 months from the production date in its original, undamaged and unopened packaging, provided storage conditions are observed. STORAGE : It must be stored between +5 °C and 30 °C. It must be protected from frost, moisture, and direct sunlight. For the product's technical specifications and other information, please download the TDS document.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: Therm 005 roof & terrace, Elastomeric resin-based, modified through special processes with various products possessing high insulation properties containing trapped air, lightweight volcanic craters, and vacuumed natural spheres turned into bubbles by expanding silicate melted at 2400 °C...
DESCRIPTION: DTDS 1704 is a cement-based, polymer-modified, fiber-reinforced, water-repellent coating material used as an exterior facade top-coat plaster.
DESCRIPTION: DTY 1702 is a cement-based, polymer-modified, fiber-reinforced adhesive and plaster mortar developed for bonding thermal insulation boards (EPS, XPS, rock wool, heat and sound insulation felt, etc.) to the substrate and plastering over them.
DESCRIPTION: DSÇ 1705 is a cement-based, polymer-modified, fiber-reinforced, water-repellent, line-patterned coating material used as an exterior facade top-coat plaster.