DESCRIPTION: MicroFloor MB 1004 MFB is formulated with a combination of special cements, high-purity mineral fillers, functional polymer binders and new generation chemical additives for floors exposed to industrial, parking and heavy traffic loads, applied by hand or pump, cement-based a...
PRODUCT INFORMATION ; DESCRIPTION: MicroFloor MB 1004 MFB is a cement-based fluid micro-concrete floor coating mortar formulated with a combination of special cements, high-purity mineral fillers, functional polymer binders and new generation chemical additives for floors exposed to industrial, parking and heavy traffic loads, which can be applied by hand or pump. It is developed to be applied in a thickness of 4 mm to 15 mm in a single layer. Containing high-performance plasticizers and superplasticizers, it is an eco-friendly system with high early and final mechanical strength. AREAS OF USE •In indoor and outdoor industrial, warehouse and production facility floors, in order to obtain a long-lasting, high-strength and dust-free surface, •In open and closed parking areas requiring fast service and opening to traffic time, •In floors with very heavy pedestrian and light vehicle traffic such as hospitals, schools, airports, metro stations and shopping malls, •It is used as a topcoat finish for leveling, structurally rehabilitating, and smoothing existing concrete floors. PRODUCT FEATURES •High Industrial Strength: Possesses excellent compressive, flexural, and abrasion resistance against aggressive pedestrian and vehicular traffic. •Excellent Self-Leveling and Flowability: Thanks to its self-spreading performance, it creates smooth and perfectly level surfaces with zero defects. •Fast Service Time (Rapid Traffic Opening): Can be opened to pedestrian traffic 2 to 4 hours after application, light vehicle traffic after 24 hours, and full heavy-load traffic after 7 days. Provides maximum savings in time and labor for projects. •Low Shrinkage and Stress: Features a formulation that minimizes the risk of cracking and blistering in large-area applications. •Casein and Protein Free: Since it does not contain casein or other organic protein derivatives, it does not allow microbiological growth (mold, bacteria); it is completely safe for hospitals and food facilities. •Decorative Alternatives: Can be produced in different colors in accordance with specification requirements. HYDRATION AND LIQUID ABSORPTION PROTECTION PROTOCOL (POLISHING / SEALING) IMPORTANT TECHNICAL NOTE: MicroFloor MB 1004 MFB has a high-performance cement-based matrix structure. Due to the nature of cement, microscopic pores (micro-voids) occur during the hydration (chemical reaction and setting) process due to the evaporation of water within the mortar. To completely prevent industrial liquids, oils, chemicals, or water that may be spilled onto the surface during the service stage after curing from being absorbed by these pores, preventing stain formation and aesthetic color discolored degradation (reducing liquid absorption to zero); it is mandatory to seal the surface with a suitable protective polish, varnish, or protective coating (topcoat/sealer) system. The polish layer preserves the color integrity of the floor while providing the surface with maximum hygiene, easy cleanability, and increased abrasion resistance. TECHNICAL SPECIFICATIONS •Compressive Strength: > 40 N/mm² •Flexural Strength: > 8 N/mm² •Adhesion to Concrete (SS 92 35 07): > 3 N/mm² •Free shrinkage: 0.04 – 0.06% •MINTEC ring test (SS 92 35 19): 145 – 155 mm •Pot life (ready-mix usable time): 15 – 20 minutes •pH value: Approximately 11 •Hardening time (foot traffic): 2 – 4 hours •Curing Time (Light Vehicle Traffic): 24 hours •Curing Time (Heavy Load Traffic): 7 days •Application Thickness: 4 – 15 mm (Layer thickness on lightweight concrete floors should be limited to 6 – 10 mm) •Dry material consumption: 1.7 kg/m² (for 1 mm thickness) (depends on the surface to be applied) APPLICATION METHODOLOGY A. Surface Preparation •It must be determined that the substrate to be applied is hard, load-bearing, dry, and structurally sound. •The substrate must be completely freed from all foreign substances that would weaken adhesion, such as cement slurry, weak layers, dust, old coatings, oil, grease, diesel, and epoxy residues, by mechanical methods (shot-blasting, milling, grinding, or shot-blasting). •Areas deeply impregnated with oil must be burned off with a torch and/or cleaned with industrial oil cleaners. The prepared surface must be cleaned with a high-suction industrial vacuum. B. Priming •E 720 EMC primer must be applied homogeneously with a soft brush, roller, or primer pump to the floor where surface preparation is completed, without allowing pooling.•The drying time of the primer is 2 – 4 hours under normal conditions. •On high-absorbency substrates: E 720 EMC primer must be applied in two coats, diluted with clean water at a ratio of 1:5 (Primer:Water) for the 1st coat, and 1:3 for the 2nd coat. •On sound industrial concrete surfaces: A single coat application diluted at a ratio of 1:3 is sufficient. •For applications to be made on special or variable substrate types, please consult the Dolphinfix technical support department for dilution ratios and technical details. •Primer application must not be carried out if the substrate and ambient temperature are below +10 °C, and the ambient relative humidity is above 70%. Insufficient drying and adverse ambient conditions may prevent the primer from forming a film layer. C. Mixing •A 25 kg bag of MicroFloor MB 1004 MFB must be mixed with clean and cold water at a ratio of 20% (5.00 liters). •During the mixing process, an original paddle mixer attached to a drill of suitable speed or integrated pumping equipment approved by Dolphinfix must be used. •The mixing time with the paddle must be continuously at least 2 minutes. After obtaining a homogeneous mixture, the material must be consumed within 15 – 20 minutes. •During mixing, the material temperature must be between +5 °C and +20 °C. Storage of the dry powder material in an excessively hot or cold environment prior to application may adversely affect the fluidity and leveling characteristics of the product. D. Application •The homogeneously mixed material is poured onto the surface in a continuous line. •The poured material must be spread onto the surface using a steel trowel, spreader rake, or screed board, and then rolled in cross directions with a spike roller to release air bubbles entrapped within the mortar and to achieve consolidation of the material. •Semi-set material can be easily shaped or cut; necessary corrections can be made at this stage. •During application and for the first 48 hours thereafter, the substrate and ambient temperature must not be colder than +10 °C, and the substrate must be protected against frost. The ambient relative humidity must be kept below 70%. •Mild ventilation is recommended during and after application, but there must be no dehumidifiers or aggressive air circulation in the environment for the first two days to prevent stress cracking due to rapid drying. The use of a curing membrane is not required. •Moving structures, structural cracks, and expansion joints in the existing sub-concrete must be transferred directly as joints onto the MicroFloor coating. WATER AND CHEMICAL RESISTANCE •Water Resistance: Pouring water on fully cured MicroFloor series products does not harm the material. However, continuous and prolonged immersion of the material under water may lead to a loss of mechanical strength. Following the removal of water and a 24-hour drying period, the material regains its original high strength values. •Chemical Resistance: The chemical resistance of the product is similar in nature to high-quality industrial concretes. If there is a risk that the floor will be continuously exposed to aggressive chemicals, acids, or solvents, the surface must be protected with suitable chemically resistant topcoat systems. LIMITATIONS AND POINTS TO NOTE •Application at temperatures below +5 °C and above +35 °C is strictly not recommended. •In exterior applications, the surface must be protected from direct sunlight, wind, rain, or frost for the first 24 hours. •The working and reaction times of cement-based systems are directly affected by ambient/substrate temperature and relative humidity in the air. At low temperatures, hydration slows down; this extends the pot life but delays the setting time. High temperatures accelerate hydration and shorten the working time. •Application thickness limits (4 – 15 mm) must be strictly complied with. In order not to exceed the tolerance limits of the material and to optimize consumption, excessive elevation differences and deep voids on the existing surface must be pre-filled with MicroFloor RM 1000 MRM repair mortar. CLEANING OF TOOLS All tools and equipment used immediately after application must be washed with water. Hardened material can only be cleaned from the surface by mechanical methods. PACKAGING, STORAGE AND SHELF LIFE •Packaging: 25 kg kraft bag. •Storage: Store in unopened original packaging in a cool, dry and moisture-free environment, protected from frost. Stack a maximum of 8 bags on top of each other. •Shelf life: 6 months from the production date under the specified suitable storage conditions.
Your orders are shipped within 1-3 business days. Shipping is free on orders of 500 ₺ and above. You can return the product within 14 days after receiving it.
Log in, you can write a review if you have purchased this product.
DESCRIPTION: MicroFloor RM 1000 MRM is a high-strength, self-spreading (flowable) floor repair and filling mortar developed with a combination of special cements, high-quality mineral fillers, polymer binders and new-generation functional chemical admixtures.
DESCRIPTION: MicroFloor MB 1003 MFB is a cement-based flowable micro-concrete (microtopping) floor coating mortar that can be applied by hand or pump, consisting of special cements, quality mineral fillers, high-performance polymer binders and new-generation functional chemical admixtures.